Difference between revisions of "SU748"
(→Back Connector) |
(→Back Connector) |
||
| Line 16: | Line 16: | ||
SU748 pin table 1(direction shown for the SU board!) | SU748 pin table 1(direction shown for the SU board!) | ||
| − | power | + | power in +5V 2 1 +5V in power |
| − | + | * out I2C_SCL_FX3 4 3 I2C_SCL_FX3 - * | |
| − | + | power in GND 6 5 - - NC | |
| − | + | power in GND 8 7 - - NC | |
| − | + | LVTTL bidir DQ1 10 9 - - NC | |
| − | + | LVTTL bidir DQ2 12 11 - - NC | |
| − | + | power in GND 14 13 - - NC | |
| − | + | LVTTL bidir DQ4 16 15 - - NC | |
| − | + | LVTTL bidir DQ7 18 17 - - NC | |
| − | + | power in GND 20 19 - - NC | |
| − | LVTTL | + | LVTTL bidir DQ8 22 21 - - NC |
| − | LVTTL | + | LVTTL bidir DQ14 24 23 - - NC |
| − | + | power in GND 26 25 - - NC | |
| − | LVTTL | + | LVTTL bidir DQ12 28 27 - - NC |
| − | + | LVTTL bidir DQ11 30 29 - - NC | |
| − | + | * bidir UART_RX/SPI_MOSI 32 31 UART_TX/SPI_MISO bidir * | |
| − | + | * bidir UART_CTS/SPI_SSN 34 33 - - NC | |
| − | power | + | power in GND 36 35 GND in power |
Revision as of 11:36, 7 August 2015
Contents
Description
This module provides a super speed USB3.0 Interface for the LogicBox in association with the Cypress FX3 USB3.0 controller. Due to the 32-Bit parallel Data-BUS, the submdoule was designed as a double SU-Board with two SU-Connectors. The hole board can be supplied by the +5V-supply of the USB-Port or the +5V-supply of the LogicBox. To protect the FX3 controller against a faulty VBUS voltage from the USB-Port, the USB charger port protection chip TPD4S014 was used. The FX3-Chip provides several serial interfaces like I²S, I²C, SPI and UART to connect to external peripherals. With the implemented I²C register PCA9555 configured by I²C or the 8-Pin DIP-Switch, some status information can be displayed on eight LEDs at the frontpanel.
Block Diagram
Front panel
Back Connector
SU748 pin table 1(direction shown for the SU board!)
power in +5V 2 1 +5V in power
* out I2C_SCL_FX3 4 3 I2C_SCL_FX3 - *
power in GND 6 5 - - NC
power in GND 8 7 - - NC
LVTTL bidir DQ1 10 9 - - NC
LVTTL bidir DQ2 12 11 - - NC
power in GND 14 13 - - NC
LVTTL bidir DQ4 16 15 - - NC
LVTTL bidir DQ7 18 17 - - NC
power in GND 20 19 - - NC
LVTTL bidir DQ8 22 21 - - NC
LVTTL bidir DQ14 24 23 - - NC
power in GND 26 25 - - NC
LVTTL bidir DQ12 28 27 - - NC
LVTTL bidir DQ11 30 29 - - NC
* bidir UART_RX/SPI_MOSI 32 31 UART_TX/SPI_MISO bidir *
* bidir UART_CTS/SPI_SSN 34 33 - - NC
power in GND 36 35 GND in power
SU748 pin table 2(direction shown for the SU board!)
power in +5V 2 1 +5V in power
NC - - 4 3 - - NC
NC - - 6 5 - - NC
NC - - 8 7 - - NC
NC - - 10 9 - - NC
NC - - 12 11 - - NC
NC - - 14 13 - - NC
NC - - 16 15 - - NC
NC - - 18 17 - - NC
NC - - 20 19 - - NC
LVTTL out SDIN 22 21 - - NC
LVTTL in SCLK 24 23 - - NC
LVTTL in CSn 26 25 - - NC
LVTTL in SDOUT 28 27 - - NC
NC - - 30 29 - - NC
NC - - 32 31 - - NC
NC - - 34 33 - - NC
power in GND 36 35 GND in power
Power consumption
Version 0
+5V -> XX mA
-5V -> XX mA
Measurement
Version 0
Compatibility
This module is compatible with all base boards
