Difference between revisions of "SU704"
(→Description) |
(→Block Diagram) |
||
| Line 34: | Line 34: | ||
= Block Diagram = | = Block Diagram = | ||
| + | |||
| + | [[File:SU704-1_block_diagram.png]] | ||
| + | |||
| + | [[File:SU704-2_block_diagram.png]] | ||
= Front planel = | = Front planel = | ||
Revision as of 08:35, 10 September 2014
Contents
Description
This module consist of 5 channel digital input/output (DIO) and 5 LEDs. Each channel can be set to work under the NIM or TTL standard independently, both of them can drive 50 Ohm impedances. If you use a channel as NIM input a 50 Ohm termination resistor must be connected to avoid reflections, this resistor can be connected through software in the version 1 of the hardware or with the help of a jumper in version 2. For all signals was used LEMO connectors. The maximal work frequency is 100 MHz. There are three hardware version of this module. The Version 0 is not used anymore. The only difference between the version 1 and 2 is that in version 1 the termination resistor can be connected through software and by the version 2 a solder jumper must to be set. The version 2 should have a better noise performance. The DIO/LED number has been inverted in the FPGA software to match the order of the SU700 module. The LED1 in FPGA connector corresponds the LED5 at the front panel.
| Version | -5V converter | Input impedance (50 Ohm/open) | Standard (TTL/NIM) |
|---|---|---|---|
| 0 | DC-DC | jumper | jumper |
| 1 | DC-DC | software | jumper |
| 2 | Linear | solder jumper | solder jumper |
Block Diagram
Front planel
Version 0
| Pos (top view) | Name | Type | Qty. | Dir. | Function |
|---|---|---|---|---|---|
| 1 LEFT | TTL/NIM input | LEMO connector | 1x | input | Digital TTL/NIM input |
| 1 RIGHT | LED1 | LED | 1x | output | LED indicator |
| 2 LEFT | Digital input/output 2 | LEMO connector | 1x | input/output | Digital input/output set by jumper/software |
| 2 RIGHT | LED2 | LED | 1x | output | LED indicator |
| 3 LEFT | Digital input/output 3 | LEMO connector | 1x | input/output | Digital input/output set by jumper/software |
| 3 RIGHT | LED3 | LED | 1x | output | LED indicator |
| 4 LEFT | Digital input/output 4 | LEMO connector | 1x | input/output | Digital input/output set by jumper/software |
| 4 RIGHT | LED4 | LED | 1x | output | LED indicator |
| 5 LEFT | Digital TTL/NIM output | LEMO connector | 1x | output | Digital TTL/NIM output |
| 5 RIGHT | LED5 | LED | 1x | output | LED indicator |
Version 1 and 2
| Pos (top view) | Name | Type | Qty. | Dir. | Function |
|---|---|---|---|---|---|
| 1 LEFT | Digital input/output 1 | LEMO connector | 1x | input/output | Digital input/output set by jumper/software |
| 1 RIGHT | LED1 | LED | 1x | output | LED indicator |
| 2 LEFT | Digital input/output 2 | LEMO connector | 1x | input/output | Digital input/output set by jumper/software |
| 2 RIGHT | LED2 | LED | 1x | output | LED indicator |
| 3 LEFT | Digital input/output 3 | LEMO connector | 1x | input/output | Digital input/output set by jumper/software |
| 3 RIGHT | LED3 | LED | 1x | output | LED indicator |
| 4 LEFT | Digital input/output 4 | LEMO connector | 1x | input/output | Digital input/output set by jumper/software |
| 4 RIGHT | LED4 | LED | 1x | output | LED indicator |
| 5 LEFT | Digital input/output 5 | LEMO connector | 1x | input/output | Digital input/output set by jumper/software |
| 5 RIGHT | LED5 | LED | 1x | output | LED indicator |
Back Connector
Version 0
SU704 pin table (direction shown for the SU board!)
power in +5V 2 1 +5V in power LVTTL in IN<4> 4 3 OUT<4> out LVTTL LVTTL in IN<3> 6 5 OUT<3> out LVTTL LVTTL in IN<2> 8 7 OUT<2> out LVTTL LVTTL in IN<1> 10 9 OUT<1> out LVTTL LVTTL in NIM<4> 12 11 NIM<3> out LVTTL LVTTL in NIM<2> 14 13 NIM<1> in LVTTL LVTTL in LED<5> 16 15 LED<4> out LVTTL LVTTL in LED<3> 18 17 LED<2> out LVTTL LVTTL in LED<1> 20 19 - - NC NC - - 22 21 - - NC NC - - 24 23 - - NC NC - - 26 25 - - NC NC - - 28 27 - - NC NC - - 30 29 - - NC NC - - 32 31 - - NC NC - - 34 33 - - NC power in - 36 35 GND in power
Version 1
SU704 pin table (direction shown for the SU board!)
power in +5V 2 1 +5V in power
LVTTL in OUTP<5> 4 3 INTTL<5> out LVTTL
LVTTL in OE_n<5> 6 5 INECL<5> out LVTTL
LVTTL in TERM<5> 8 7 LED_n<5> in LVTTL
LVTTL in OUTP<4> 10 9 INTTL<4> out LVTTL
LVTTL in OE_n<4> 12 11 INECL<4> out LVTTL
LVTTL in TERM<4> 14 13 LED_n<4> in LVTTL
LVTTL in OUTP<3> 16 15 INTTL<3> out LVTTL
LVTTL in OE_n<3> 18 17 INECL<3> out LVTTL
LVTTL in TERM<3> 20 19 LED_n<3> in LVTTL
LVTTL in OUTP<2> 22 21 INTTL<2> out LVTTL
LVTTL in OE_n<2> 24 23 INECL<2> out LVTTL
LVTTL in TERM<2> 26 25 LED_n<2> in LVTTL
LVTTL in OUTP<1> 28 27 INTTL<1> out LVTTL
LVTTL in OE_n<1> 30 29 INECL<1> out LVTTL
LVTTL in TERM<1> 32 31 LED_n<1> in LVTTL
NC - - 34 33 - - NC
power in GND 36 35 GND in power
Version 2
SU704 pin table (direction shown for the SU board!)
power in +5V 2 1 +5V in power
LVTTL in OUTP<5> 4 3 INTTL<5> out LVTTL
LVTTL in OE_n<5> 6 5 INECL<5> out LVTTL
NC in - 8 7 LED_n<5> in LVTTL
LVTTL in OUTP<4> 10 9 INTTL<4> out LVTTL
LVTTL in OE_n<4> 12 11 INECL<4> out LVTTL
NC in - 14 13 LED_n<4> in LVTTL
LVTTL in OUTP<3> 16 15 INTTL<3> out LVTTL
LVTTL in OE_n<3> 18 17 INECL<3> out LVTTL
NC in - 20 19 LED_n<3> in LVTTL
LVTTL in OUTP<2> 22 21 INTTL<2> out LVTTL
LVTTL in OE_n<2> 24 23 INECL<2> out LVTTL
NC in - 26 25 LED_n<2> in LVTTL
LVTTL in OUTP<1> 28 27 INTTL<1> out LVTTL
LVTTL in OE_n<1> 30 29 INECL<1> out LVTTL
LVTTL in - 32 31 LED_n<1> in LVTTL
NC - - 34 33 - - NC
power in GND 36 35 GND in power
