Time to digital converter (TDC)

LogicPool (TDC)

This module is a software implementation, no need of hardware to work. The TDC will capture the time stamp of the input channels by rising edge so long the gate is activated. The maximal time resolution is 10 ns and can be changed through a programmable divider, an external signal can be used as TDC clock too.

This module has a bus interface to connect with a FIFO, in this FIFO will be written the channel and time information of each rising edge, so long the gate is active. The number of channels and length of the time stamp counters depends on the selected model.

During the gate a package will be written in the FIFO. This package can consists of a Start of gate marker, 0 to N events marker and a stop of gate marker.

Models

At this time there are two models. The model 0 has only one event channel and the model 1 8 event channels. The event marker are different for each model. The model 0 event marker is a 32-bits time information and the model 1 event marker consist of 8-Bit channel mask to indicate which channels has been toggle and 24-bit with the time stamp

TDC model 1 Package overview

Event	Channel info (bits 31..24)	Time stamp (bits 23..0)	Explanation
SOG	0x00	0x000000	SOG = start of gate, time stamp will be always 0 and no active channels
E1	0x01	0x000064	detected a rising edge on channel 0 100 CLKs after the SOG
E2	0x03	0x000080	detected a rising edge on channel 0 and 1 128 CLKs after the SOG
E3	0x00	0xFFFFFF	time stamp counter overflow
E4	0x80	0x0001FF	detected a rising edge on channel 7 16777215+511 CLKs after the SOG
EOG	0x00	0x0003FF	EOG = end of gate, no active channels and time stamp must be non zero

CBUS Address

Register Map Model 0

Module Address: 'B' or Ox42

Read register

Read registers

Register Address	Name	Data
0	MUX_IN	Bit 7..0: multiplexer address
1	EVENT MARKER	Bit 31..0: current event information

Write register

Write registers

Register Address	Name	Data
0	MUX_GATE	Bit 7..0: gate multiplexer address
1	MUX_CLOCK	Bit 7..0: clock multiplexer address
2	CLOCK_DIVIDER	Bit 31..0:
3	MUX_EVENT_CHANNEL	Bit 7..0: event channel multiplexer address

Register Map Model 1

Module Address: 'B' or Ox42

Read register

Read registers

Register Address	Name	Data
0	MUX_IN	Bit 7..0: multiplexer address
1	EVENT MARKER	Bit 31..0: current event information

Write register

Write registers

Register Address	Name	Data
0	MUX_GATE	Bit 7..0: gate multiplexer address
1	MUX_CLOCK	Bit 7..0: clock multiplexer address
2	CLOCK_DIVIDER	Bit 31..0:
3	MUX_EVENT_CHANNEL_0	Bit 7..0: event channel 0 multiplexer address
4	MUX_EVENT_CHANNEL_1	Bit 7..0: event channel 1 multiplexer address
5	MUX_EVENT_CHANNEL_2	Bit 7..0: event channel 2 multiplexer address
6	MUX_EVENT_CHANNEL_3	Bit 7..0: event channel 3 multiplexer address
7	MUX_EVENT_CHANNEL_4	Bit 7..0: event channel 4 multiplexer address
8	MUX_EVENT_CHANNEL_5	Bit 7..0: event channel 5 multiplexer address
9	MUX_EVENT_CHANNEL_6	Bit 7..0: event channel 6 multiplexer address
10	MUX_EVENT_CHANNEL_7	Bit 7..0: event channel 7 multiplexer address
11	CONF_REG	Bit 0: disable end of gate (EOG) Bit 1: disable start of gate (SOG) Bit 2: retrigger
12	GATE_TIME	Bit 31..0: if this value is set to 0 the end of gate will be controlled through the gate input, otherwise the gate will be a duration of this value x clock period
13	DATA_DELAY	Bit 2..0:

LabVIEW Vi

Inputs

 Input 1: 
 Input 2:

Outputs

 Output 1: 
 Output 2:

Parameters

 Param 1: 
 Param 2:

Functions

 Function 1: 
 Function 2: