Difference between revisions of "SU751"
(Created page with "SU751 can accomodate 5 small sub-modules (here numbered from 1 to 5), each connected thorugh 3 I/Os to the SU751 connector and so to the FPGA. Pin table (direction shown for ...") |
|||
| Line 29: | Line 29: | ||
A-1: | A-1: | ||
| + | |||
| + | {| border="1" class="wikitable" | ||
| + | |+ Submodules for SU751 | ||
| + | ! Name !! Isolated? !! Used power !! Pin INP !! Pin OUTP !! Pin OE_n !! Comment | ||
| + | |- | ||
| + | ! A-0 Comparator | ||
| + | | no || -5V,+5V,+3.3V || Comparator Output || - || - || INP=1 when LEMO > threshold | ||
| + | |- | ||
| + | ! A-1 Comparator with DAC | ||
| + | | no || -5V,+5V,+3.3V || Comparator Output || SDA || SCL || INP=1 when LEMO > threshold | ||
| + | |- | ||
| + | ! A-1 12-bit DAC | ||
| + | | no || -5V,+5V,+3.3V || - || SDA || SCL || INP is DAC output, options: 0..4.095V, +/-4.095V, +/-2.047V | ||
| + | |} | ||
Revision as of 09:30, 16 January 2018
SU751 can accomodate 5 small sub-modules (here numbered from 1 to 5), each connected thorugh 3 I/Os to the SU751 connector and so to the FPGA.
Pin table (direction shown for the SU board!)
power in +5V 2 1 +5V in power LVTTL in OUTP<5> 4 3 INP<5> out LVTTL LVTTL in OE_n<5> 6 5 INJ<5> GND in GND 8 7 LED_n<5> in LVTTL LVTTL in OUTP<4> 10 9 INTTL<4> out LVTTL LVTTL in OE_n<4> 12 11 INJ<4> GND in GND 14 13 LED_n<4> in LVTTL LVTTL in OUTP<3> 16 15 INTTL<3> out LVTTL LVTTL in OE_n<3> 18 17 INJ<3> GND in GND 20 19 LED_n<3> in LVTTL LVTTL in OUTP<2> 22 21 INTTL<2> out LVTTL LVTTL in OE_n<2> 24 23 INJ<2> GND in GND 26 25 LED_n<2> in LVTTL LVTTL in OUTP<1> 28 27 INTTL<1> out LVTTL LVTTL in OE_n<1> 30 29 INJ<1> GND in GND 32 31 LED_n<1> in LVTTL NC - - 34 33 GND - GND power in GND 36 35 GND in power
Note: 1) INJ<1..5> can be jumpered on SU751 to INP<1..5> in order to be fullly compatible to SU704. Normally not necessary. 2)The additional GND pins can be connector in the FPGA as outputs driving 0. Be carefull not to drive 1! 3) The LEDs are active low, like in SU704.
List of the sub-modules for SU751.
A-0: Comparator with LT1719, the threshold can be bipolar and set by resistors. The output of the comparator is high when the input is higher than the threshold and is mapped to the INP<n> port. OE_n<n> and OUTP<n> are not connced.
A-1:
| Name | Isolated? | Used power | Pin INP | Pin OUTP | Pin OE_n | Comment |
|---|---|---|---|---|---|---|
| A-0 Comparator | no | -5V,+5V,+3.3V | Comparator Output | - | - | INP=1 when LEMO > threshold |
| A-1 Comparator with DAC | no | -5V,+5V,+3.3V | Comparator Output | SDA | SCL | INP=1 when LEMO > threshold |
| A-1 12-bit DAC | no | -5V,+5V,+3.3V | - | SDA | SCL | INP is DAC output, options: 0..4.095V, +/-4.095V, +/-2.047V |
